We've launched our new site at www.openlighting.org. This wiki will remain and be updated with more technical information.
Difference between revisions of "ArtNet"
From wiki.openlighting.org
(added wiki links, removed spelling errors) |
|||
| (3 intermediate revisions by 2 users not shown) | |||
| Line 5: | Line 5: | ||
==What is DMX?== | ==What is DMX?== | ||
| − | DMX is a standard for controlling theater equipment (mainly lighting). In a theater, there are normally large numbers of lights, that have to be turned on and off independently. One solution to this is to wire the theater like a | + | [[DMX]] is a standard for controlling theater equipment (mainly lighting). In a theater, there are normally large numbers of lights, that have to be turned on and off independently. One solution to this is to wire the theater like a house and have a desk of on/off switches with a mains cable running to each light. |
There are a couple of issues with this however. First, mains cables are relatively thick, even with 20 lights and 20 cables, a lot of wire is involved. Secondly, if we ever wanted to move the desk, we'd have to run a new wire for every light which is most theaters would be a horrendous job. Finally, doing the same thing many times isn't the way we engineers like to work :) | There are a couple of issues with this however. First, mains cables are relatively thick, even with 20 lights and 20 cables, a lot of wire is involved. Secondly, if we ever wanted to move the desk, we'd have to run a new wire for every light which is most theaters would be a horrendous job. Finally, doing the same thing many times isn't the way we engineers like to work :) | ||
| Line 15: | Line 15: | ||
| − | In a DMX cable, only 3 of the 5 pins are used (signal +, signal -, and ground) | + | In a [[DMX]] cable, only 3 of the 5 pins are used (signal +, signal -, and ground). |
| − | |||
| − | |||
| + | A DMX network is formed in a daisy chain fashion, so one device is the source (most often the lighting control console) and the other devices are the receivers. Each receiver has a preset address, which corresponds to the channels of DMX data (from 1 to 512) that it is interested in. | ||
==What are IP Networks?== | ==What are IP Networks?== | ||
| − | Like DMX, IP is a protocol. Where as DMX connects lighting equipment, IP was designed to connect computers. For the scope of this discussion, IP operates on top of another protocol called Ethernet. | + | Like DMX, IP is a protocol. Where as DMX connects lighting equipment, IP was designed to connect computers. For the scope of this discussion, IP operates on top of another protocol called Ethernet. Cables are generally CAT5 and have RJ45 jacks on the end, similar to phone jacks. |
Ethernet is wired in a star fashion (extended star to be precise), so an Ethernet network looks a bit like this: | Ethernet is wired in a star fashion (extended star to be precise), so an Ethernet network looks a bit like this: | ||
| − | |||
==ArtNet and DMX== | ==ArtNet and DMX== | ||
| Line 33: | Line 31: | ||
* An ethernet cable can carry a lot more information than a DMX cable (Part of my work is to identify exactly how much is "a lot"). | * An ethernet cable can carry a lot more information than a DMX cable (Part of my work is to identify exactly how much is "a lot"). | ||
* Hardware for ethernet networks is much cheaper than DMX networks | * Hardware for ethernet networks is much cheaper than DMX networks | ||
| − | * IP is not tied to a single | + | * IP is not tied to a single physical medium, this means it's as easy to send the DMX data via wireless links as it is to send it down wireless. Coupled with point two, this means we can have very low cost wireless DMX links. |
* Continuing from point three, this means that it's also easy to send DMX data over the Internet. Ever wanted to control your lights from a suburb away? | * Continuing from point three, this means that it's also easy to send DMX data over the Internet. Ever wanted to control your lights from a suburb away? | ||
| − | * ArtNet supports bi-directional communication, this means that nodes can send information back to the controllers (DMX also supports this via RDM, but you may have to upgrade your equipment). | + | * ArtNet supports bi-directional communication, this means that nodes can send information back to the controllers (DMX also supports this via [[RDM]], but you may have to upgrade your equipment). |
Latest revision as of 06:15, 9 December 2009
ArtNet is a protocol for sending DMX data over IP networks developed by Artistic Licence. In order to understand ArtNet it helps to know a bit about DMX and IP, so here it goes....
What is DMX?
DMX is a standard for controlling theater equipment (mainly lighting). In a theater, there are normally large numbers of lights, that have to be turned on and off independently. One solution to this is to wire the theater like a house and have a desk of on/off switches with a mains cable running to each light.
There are a couple of issues with this however. First, mains cables are relatively thick, even with 20 lights and 20 cables, a lot of wire is involved. Secondly, if we ever wanted to move the desk, we'd have to run a new wire for every light which is most theaters would be a horrendous job. Finally, doing the same thing many times isn't the way we engineers like to work :)
So, instead of a cable from the desk to every light. why not put all the mains switching gear near the lights and run a low voltage control signal from the desk? Sounds good? Well thats exactly what DMX does.
DMX is a serial protocol, so it sends data one bit at a time over the wire. Each DMX cable can control up to 512 channels (for now, each channel is a light) and each channel takes a value between 0 and 255. If conventional lights are being used, each light occupies a single channel and the value of the channel is the intensity of the light (0 = off, 255 = full).
In a DMX cable, only 3 of the 5 pins are used (signal +, signal -, and ground).
A DMX network is formed in a daisy chain fashion, so one device is the source (most often the lighting control console) and the other devices are the receivers. Each receiver has a preset address, which corresponds to the channels of DMX data (from 1 to 512) that it is interested in.
What are IP Networks?
Like DMX, IP is a protocol. Where as DMX connects lighting equipment, IP was designed to connect computers. For the scope of this discussion, IP operates on top of another protocol called Ethernet. Cables are generally CAT5 and have RJ45 jacks on the end, similar to phone jacks.
Ethernet is wired in a star fashion (extended star to be precise), so an Ethernet network looks a bit like this:
ArtNet and DMX
Back to ArtNet. ArtNet then is a way of sending DMX information over IP networks. So what are the advantages ?
- An ethernet cable can carry a lot more information than a DMX cable (Part of my work is to identify exactly how much is "a lot").
- Hardware for ethernet networks is much cheaper than DMX networks
- IP is not tied to a single physical medium, this means it's as easy to send the DMX data via wireless links as it is to send it down wireless. Coupled with point two, this means we can have very low cost wireless DMX links.
- Continuing from point three, this means that it's also easy to send DMX data over the Internet. Ever wanted to control your lights from a suburb away?
- ArtNet supports bi-directional communication, this means that nodes can send information back to the controllers (DMX also supports this via RDM, but you may have to upgrade your equipment).
