Personal tools
The Open Lighting Project has moved!

We've launched our new site at www.openlighting.org. This wiki will remain and be updated with more technical information.

Difference between revisions of "OLA LED Pixels"

From wiki.openlighting.org

Jump to: navigation, search
m (Host Hardware)
Line 47: Line 47:
 
On the pixel side the following is supported:
 
On the pixel side the following is supported:
 
* LPD8806, e.g. https://www.adafruit.com/products/306.  since 0.8.27
 
* LPD8806, e.g. https://www.adafruit.com/products/306.  since 0.8.27
* WS2801, e.g. https://www.adafruit.com/products/738, since 0.8.38
+
* WS2801, e.g. https://www.adafruit.com/products/738, since 0.8.28
  
  
Line 54: Line 54:
 
The simplest setup is to connect SCLK (pin 23) to the pixel string's clock line and MOSI (pin 19) to the pixel string's DATA line. You'll need a separate power supply for the pixel string, check the pixel specifications but 1A per m is a good rule of thumb. Don't forget to connect the ground on the power supply to a ground pin (e.g. 25) on the Pi.Do not connect the 5V rail of the pixel power supply to the Pi.
 
The simplest setup is to connect SCLK (pin 23) to the pixel string's clock line and MOSI (pin 19) to the pixel string's DATA line. You'll need a separate power supply for the pixel string, check the pixel specifications but 1A per m is a good rule of thumb. Don't forget to connect the ground on the power supply to a ground pin (e.g. 25) on the Pi.Do not connect the 5V rail of the pixel power supply to the Pi.
  
 +
=== Multiplexer ===
 +
 +
 +
If you want to drive more than one string in parallel you'll need to use a de-multiplexer. For a two-line multiplexer one can use the CE0 and CE1 lines to select the output string. To run more than 2 strings you'll need to use some of the GPIO pins as chip-enables.
 +
 +
TODO: post schematic here
 +
 +
 +
 +
== OLA SPI Plugin ==
 +
 +
The [[OLA]] SPI plugin is pretty flexible.
  
=== Multiplexer ===
 
  
 
== Software Setup ==
 
== Software Setup ==
Line 86: Line 97:
 
spidev0.1-spi-speed = 100000
 
spidev0.1-spi-speed = 100000
 
</pre>
 
</pre>
 +
 +
== Sample Configs ==
 +
 +
=== Single Pixel String ===
 +
 +
 +
=== Two Pixel Strings, using the CE lines ===
 +
 +
  
 
== Related Links ==
 
== Related Links ==
  
 
http://www.solderlab.de/index.php/software/glediator (Pixel Control Software that outputs ArtNet)
 
http://www.solderlab.de/index.php/software/glediator (Pixel Control Software that outputs ArtNet)

Revision as of 09:17, 14 September 2013

Lpd8806.jpeg

Since March 2013, OLA contains an SPI plugin, which allows you to drive strings of LEDs pixels provided your platform has an SPI interface. Using embedded Linux platforms like the Raspberry Pi, this allows one to build Pixel strings controllable via any of the supported protocols (ArtNet, E1.31, OSC & more) for < $100.

Alternatively if you don't want network control, you can send DMX512 to the LEDs using the Python, C++ or Java client library running on the host itself.

This page is focused on the Raspberry Pi, but may be applicable to other hardware such as the BeagleBone. If you're using a Raspberry Pi you can save yourself a lot of time by using the pre-built images, see OLA on the Raspberry Pi for details.

Host Hardware

The Raspberry Pi contains three SPI interfaces, but only one of these is wired to the 26-pin connector. The interface comes with 3 chip-enable (CE) lines but again only two are connected (pins 24 & 26). With the default mode, pin 24 is pulled low when the /dev/spi0.0 device is used and pin 26 is pulled low when /dev/spi0.1 is used.

Here are some timings taken from the Pi:

SPI Speed Number of bytes time taken for write() Time on the wire
1MHz 75 13.5ms 11.1ms
2MHz 75 8.1ms 5.6ms
4MHz 75 4.7 ms 3.0 ms
8MHz 75 3.7ms 1.4ms
12MHz 75 3.2ms 0.75 ms
1MHz 516 78.5 ms 76.15 ms
2MHz 516 40.2 ms 38.2ms
4MHz 516 21.5 ms 19.1 ms
8MHz 516 12.2ms 9.6ms
12MHz 516 7.4ms 4.83 ms

It also takes somewhere between 3.6 and 4.6 ms to toggle a GPIO pin using the /sys/class/gpio interface. The importance of these numbers will be clear in a minute.


Beyond the Pi, any SPI hardware supported by the Linux kernel should work modulo the timing numbers. By default OLA looks for devices that match the /dev/spi* .

Pixel Hardware

On the pixel side the following is supported:


Hardware Setup

The simplest setup is to connect SCLK (pin 23) to the pixel string's clock line and MOSI (pin 19) to the pixel string's DATA line. You'll need a separate power supply for the pixel string, check the pixel specifications but 1A per m is a good rule of thumb. Don't forget to connect the ground on the power supply to a ground pin (e.g. 25) on the Pi.Do not connect the 5V rail of the pixel power supply to the Pi.

Multiplexer

If you want to drive more than one string in parallel you'll need to use a de-multiplexer. For a two-line multiplexer one can use the CE0 and CE1 lines to select the output string. To run more than 2 strings you'll need to use some of the GPIO pins as chip-enables.

TODO: post schematic here


OLA SPI Plugin

The OLA SPI plugin is pretty flexible.


Software Setup

You'll want to see here for suitable udev config, so OLA has permission to talk to your SPI port, as well as some Raspberry Pi specific config.


Once you have OLA running it's a matter of patching an SPI Output port to a universe and then patching the desired input port. This can be done from the OLA web UI, which runs on port 9090.

Example of an ArtNet controlled LED String

Configuration

The type of LED drivers, operating mode and DMX Start Address are configurable via RDM. Click on the RDM tab and you'll see the options.

Using RDM to set the hardware type and DMX start address


The number of LEDs and SPI speed is set using the ola-spi.conf file.

base_uid = 7a70:00000100
device_prefix = spidev
enabled = true
spidev0.0-dmx-address = 1
spidev0.0-personality = 1
spidev0.0-pixel-count = 25
spidev0.0-spi-speed = 100000
spidev0.1-dmx-address = 1
spidev0.1-personality = 2
spidev0.1-pixel-count = 25
spidev0.1-spi-speed = 100000

Sample Configs

Single Pixel String

Two Pixel Strings, using the CE lines

Related Links

http://www.solderlab.de/index.php/software/glediator (Pixel Control Software that outputs ArtNet)