NonConformDMX - Revision history

Hippy: Add Pro518 and Commet6

2012-11-30T00:17:24Z

Add Pro518 and Commet6

2010-12-09T07:07:01Z

2010-04-02T16:50:55Z

Added OpenDMX USB and clones

2009-01-28T10:26:16Z

Added horizontal line

2009-01-09T18:53:29Z

2009-01-09T18:52:59Z

2009-01-09T18:52:21Z

2008-02-20T20:11:16Z

2007-02-26T05:51:15Z

2007-02-26T05:46:51Z

← Older revision		Revision as of 00:17, 30 November 2012
Line 14:		Line 14:

	Martin RoboScan Pro400: operates with a non-zero startcode.		Martin RoboScan Pro400: operates with a non-zero startcode.
		+
		+	Martin RoboScan Pro518: operates with a non-zero startcode.
		+
		+	Note: both have 3-pin XLR connectors, and include internal jumpers to reverse polarity for use with Martin Protocol.
		+
		+	----
		+
		+	'''Theatrelight'''
		+
		+	Commet 6 - single-phase 15A dimmer pack: operates with a non-zero startcode.

	----		----

← Older revision		Revision as of 07:07, 9 December 2010
Line 16:		Line 16:

	----		----
−
−	~~'''EntTec'''~~
−
−	Open DMX USB (and clones, but not "DMX USB Pro"): As the host PC is responsible for the correct DMX timing and the USB interface is used, the timing for "Break" and "Mark after Break" is way out of the specification.
−	~~Break has a length of ca. 3ms (should be 176-352µs), Mark after Break has a length of ca. 2ms where it should have 12-88µs.~~

← Older revision		Revision as of 16:50, 2 April 2010
Line 14:		Line 14:

	Martin RoboScan Pro400: operates with a non-zero startcode.		Martin RoboScan Pro400: operates with a non-zero startcode.
		+
		+	----
		+
		+	'''EntTec'''
		+
		+	Open DMX USB (and clones, but not "DMX USB Pro"): As the host PC is responsible for the correct DMX timing and the USB interface is used, the timing for "Break" and "Mark after Break" is way out of the specification.
		+	Break has a length of ca. 3ms (should be 176-352µs), Mark after Break has a length of ca. 2ms where it should have 12-88µs.

@@ Line 1: / Line 1: @@
 Feel free to add DMX equipment that does not conform to the ESTA DMX Spec.
 '''Eurolite'''
 Eurolite ts-5: needs pause between DMX channels to work properly, standard says no pause is needed. When using with Enttec PRO and MagicQ, only movements (pan and tilt, two first channels of device) work, shutter and dimmer can't be controlled
-'''comment:''' if you use 6 channels to control the ts-5, it works a little better, but it's still not perfect. channel 4 and 5 must be coupled(have the same value) and the new 6th channel does the dimmer. But there are still some uncontrolled movements of the gobo and colour wheel, except they have the same value(ch. 3,4&5);
+'''Comment:''' If you use 6 channels to control the ts-5, it works a little better, but it's still not perfect. channel 4 and 5 must be coupled(have the same value) and the new 6th channel does the dimmer. But there are still some uncontrolled movements of the gobo and colour wheel, except they have the same value(ch. 3,4&5);
 ----

@@ Line 3: / Line 3: @@
 '''Eurolite'''
 Eurolite ts-5: needs pause between DMX channels to work properly, standard says no pause is needed. When using with Enttec PRO and MagicQ, only movements (pan and tilt, two first channels of device) work, shutter and dimmer can't be controlled
 '''comment:''' if you use 6 channels to control the ts-5, it works a little better, but it's still not perfect. channel 4 and 5 must be coupled(have the same value) and the new 6th channel does the dimmer. But there are still some uncontrolled movements of the gobo and colour wheel, except they have the same value(ch. 3,4&5);

← Older revision		Revision as of 05:51, 26 February 2007
Line 2:		Line 2:

	eurolite ts-5: needs pause between DMX channels to work properly, standard says no pause is needed		eurolite ts-5: needs pause between DMX channels to work properly, standard says no pause is needed
−	Martin Pro400: operates with a non-zero startcode.	+
		+	----
		+
		+	'''Martin'''
		+
		+	Martin RoboScan Pro400: operates with a non-zero startcode.

← Older revision		Revision as of 05:46, 26 February 2007
Line 2:		Line 2:

	eurolite ts-5: needs pause between DMX channels to work properly, standard says no pause is needed		eurolite ts-5: needs pause between DMX channels to work properly, standard says no pause is needed
		+	Martin Pro400: operates with a non-zero startcode.